AGCO EDT 1.128.24284.909 [2024.11]

AGCO

Relevant details

USD 120.00

Interfaces

Actions

Save with Crypto 15% off

Compatible interfaces

AGCO 2X4 USB

AGCO 2X4 USB

Complete information

Description The electronic diagnostic tool (EDT) can be used by technicians to connect to specific machines that have a controller area network (CAN) bus as part of the electronic system architecture. You can do complete diagnosis, programming and access the troubleshooting.
Brand AGCO
Category agricultural
File Size 40.70 GB
Size Installed 85.00 GB
Region ALL REGIONS
Operating System* WINDOWS 10 (64 BITS), WINDOWS 11 (64 BITS)
License time 3 YEARS
Database Language ENGLISH
License Type DEALER
Interface Language ENGLISH, FRENCH, FINNISH, GERMAN, SPANISH, PORTUGUESE, DANIS
Software Type DIAGNOSTIC, REPROGRAMMING
OP Not Supported* WINDOWS 10 (32 BITS), WINDOWS 7 (64 BITS), WINDOWS 7 (32 BIT
Incompatible Software CLAAS CDS, JOHN DEERE SERVICE ADVISOR, DEUTZ SERDIA

* Which OS data is supported and which is not is based on the information that Mecaprograms has verified so far. There may be other OS that we have not evaluated and that may be compatible or, failing that, may not be. Mecaprograms assumes responsibility only for the tests that we have carried out and the guarantees that we can offer based on them.

About support interfaces

No information interfaz available

Relevant features

Updates

  • "RELEASE NOTES - 11/15/2024 - UPDATE 2024.5.OC1
  • EDT NOTES:
  • EDT VERSION: 1.128.24284.909
  • VEHICLES AFFECTED:
  • MASSEY FERGUSON: 197, 235, 265
  • VEHICLE VERSION:
  • 1.36
  • SOFTWARE:
  • GD - 04.05.07
  • FIXES REARSTEER EXTEND/RETRACT SIGNAL COMMANDS SO IT WILL ONLY BE ACTIVE WHEN IN REARSTEER GEAR RANGE SELECTION. THE ISSUE WAS FOUND TO BE A PART OF THE SOFTWARE THAT WAS TRIGGERED WHEN THE MINOR VERSION NUMBER WAS CHANGED FROM .3 TO .4 OR GREATER. THIS CHANGE CAUSED THE REARSTEER CYLINDER COILS FOR EXTEND AND RETRACT TO BECOME ACTIVE IN ALL GEAR RANGES INSTEAD OF JUST REARSTEER. THE BUG IN THE SYSTEM HAS BEEN FOUND AND REMOVED FROM SOFTWARE.
  • RELEASE NOTES - 11/6/2024 - UPDATE 2024.5
  • EDT NOTES:
  • EDT VERSION: 1.128.24284.909
  • ENHANCEMENTS:
  • MINOR IMPROVEMENTS TO DIAGNOSTIC FUNCTIONALITY.
  • VEHICLES AFFECTED:
  • MASSEY FERGUSON: SQUARE BALERS: 2224, 2233, 2234, 2234XD, 2244
  • FENDT: SQUARE BALERS: 990, 1270, 1290, 1290XD, 12130
  • VEHICLE VERSION:
  • 1.32
  • GENERAL:
  • MAKE MASSEY FERGUSON MACHINES AVAILABLE IN AFRICA/MIDDLE EAST
  • DIAGNOSTICS:
  • ADD SUPPORT FOR ALL BRANDS OF KEYPADS
  • CALIBRATIONS:
  • ADD OPTIONS TO CONFIGURE DIGITAL KNOTTER POSITION AND BRAKE RELEASE.
  • SOFTWARE:
  • EXT-LITE - V01.10.00
  • WORK RECORDS NAMES CAN NOW INCLUDE FOREIGN CHARACTERS WHEN USING VTV4 OR HIGHER
  • ADD OPTION TO HIDE BRAKE RELEASE BUTTON WHEN THIS OPTION IS NOT INSTALLED THROUGH EDT
  • FIX PROBLEM WITH NOT RESETTING FLAKE COUNT IN SOME SITUATIONS
  • FIX LOST SPEED SOURCE ALARM WHEN ONLY ONE MEASUREMENT IS MISSING
  • FIX SENDING MOISTURE VALUES THAT ARE 10 TIMES AS BIG TO BALE LINK
  • FIX READING RFID TAGS
  • FIX SENDING OUT BALE DROP INFORMATION WHEN USING AN ACCUMULATOR
  • VEHICLES AFFECTED:
  • CHALLENGER: MT540, MT560, MT570, MT580
  • MASSEY FERGUSON: 7350, 7370, 7390, 7415
  • VALTRA: BT150, BT170, BT190, BT210
  • VEHICLE VERSION:
  • 4.86
  • GENERAL:
  • A NEW SOFTWARE VERSION 14.40.000.01.4 IS NOW AVAILABLE FOR UPDATING GFX-750 AND GFX-1060 MONITORS FOR TRACTORS.
  • DISABLED GFX750/1060 FOR REGIONS OUTSIDE OF SOUTH AMERICA
  • SOFTWARE:
  • GFX-750/1060 SOFTWARE VERSION 14.40.000.01.4
  • PLUG-INS:
  • GFX750 VERSION 1.4
  • VEHICLES AFFECTED:
  • CHALLENGER: 660B MADE IN BRAZIL, 670B MADE IN BRAZIL, 680B MADE IN BRAZIL
  • MASSEY FERGUSON: 9695 MADE IN BRAZIL, 9795 MADE IN BRAZIL, 9895 MADE IN BRAZIL
  • VALTRA: BC6800, BC7800, BC8800
  • VEHICLE VERSION:
  • 1.29
  • SOFTWARE:
  • AGCO CONNECTIVITY MODULE SOFTWARE VERSION 5.04.04
  • PLUG-INS:

 

  • UPDATE ACM PLUGIN TO VERSION 6.19
  • VEHICLES AFFECTED:
  • MASSEY FERGUSON: 4690, 5690, 6690
  • VALTRA**: BC4800, BC5800**
  • VEHICLE VERSION:
  • 3.18
  • SOFTWARE:
  • AGCO CONNECTIVITY MODULE SOFTWARE VERSION 5.04.04
  • PLUG-INS:
  • UPDATE ACM PLUGIN TO VERSION 6.19
  • VEHICLES AFFECTED:
  • MASSEY FERGUSON: MF9130, MF9350DRY
  • VALTRA: BS3120H, BS3350H
  • VEHICLE VERSION:
  • 4.6
  • GENERAL:
  • IMPROVED THE IDENTIFICATION OF AGI4 AND AGS2 RECEIVERS IN THE NETWORK SCAN PROCESS.
  • VEHICLES AFFECTED:
  • MASSEY FERGUSON: MF 6700S STAGE 5 SERIES
  • MASSEY FERGUSON: MF 7700S STAGE 5 SERIES
  • VEHICLE VERSION:
  • 3.11
  • SOFTWARE:
  • NEW SRC14-34 SOFTWARE V6.15 FOR DYNA-VT MODELS:
  • P20758 - FIX PTO AUTO WHICH WAS NOT WORKING IF FRONT HITCH COMMAND IS DIFFERENT THAN NEUTRAL
  • P22189 - FIX DTM STATUS WHICH WAS NOT MEMORIZED AT KEY ON/OFF/ON
  • P22422 - FIX THE FLOAT WHICH STAYED ENGAGED EVEN IF THE JOYSTICK IS IN LEFT POSITION
  • NEW SRC14-34 SOFTWARE V6.16 FOR DYNA-6 MODELS:
  • P20758 - FIX PTO AUTO WHICH WAS NOT WORKING IF FRONT HITCH COMMAND IS DIFFERENT THAN NEUTRAL
  • P22189 - FIX DTM STATUS WHICH WAS NOT MEMORIZED AT KEY ON/OFF/ON
  • P22422 - FIX THE FLOAT WHICH STAYED ENGAGED EVEN IF THE JOYSTICK IS IN LEFT POSITION
  • FIX HEADLAND SHIFT +/- FUNCTIONALITY WHICH WAS NOT WORKING SINCE V6.13
  • NEW STAGE 5 ENGINE SOFTWARE (49LFTN-D5 & 66LFTN-D5) :
  • P21403 - CHANGE ENGINE RPM AT WHICH INJECTION CUT TO AVOID STALLING WHEN ACTIVATING PTO
  • ACM
  • GW04 UPDATED TO V05.04.04 TO SUPPORT THE ENCRYPTED WIFI CONNECTION
  • GW03 REVERTED TO V05.01.06 WHICH IS THE LATEST VERSION COMPATIBLE WITH THE HARDWARE.
  • VEHICLES AFFECTED:
  • MASSEY FERGUSON: 2700-4700 SERIES
  • MASSEY FERGUSON: 6700R SERIES
  • MASSEY FERGUSON: GLOBAL SERIES 4700-5700-6700
  • VALTRA: A100
  • VALTRA: A100HITECH SERIES
  • VALTRA: A4, A4S
  • VALTRA: A4HITECH SERIES
  • VALTRA: AC52.5, AC54.5, AC56.5
  • VEHICLE VERSION:
  • 7.7
  • SOFTWARE:
  • NEW DASHBOARD CONTI CLUSTER V2.14 ONLY FOR MF MODELS
  • P24325 - GLOBAL SERIES NON-RMI HECTARS COUNTER NOT WORKING
  • NEW AUTO7 APP8 TRANS V2.33.00 ONLY FOR MF MODELS
  • P19661 - GS HARSH ENGAGEMENT WITH CLUTCH PEDAL (AUTO7)
  • P21541 - POWER SHUTTLE LEVER HARSH
  • BUG FIX : PTO CAN DISENGAGES WITHOUT ERROR CODE DUE TO FALSE DETECTION OF SPEED CHANGE
  • NEW ENGINE SOFTWARE FOR TIER4F 3 CYLINDER ENGINES (33AWFC):
  • UPDATE CALIBRATION TO IMPROVE BEHAVIOR AT INITIALIZATION AND PREVENT RAIL PRESSURE OVERSHOOTS DURING ENGINE START
  • NEW ACM SOFTWARE V05.04.04:
  • ADDED WIFI PASSWORD TO ACM
  • MANY FIXES

 

  • NEW ENGINE SOFTWARE FOR TIER4F 3 CYLINDER ENGINES (33AWFC):
  • UPDATE CALIBRATION TO IMPROVE BEHAVIOR AT INITIALIZATION AND PREVENT RAIL PRESSURE OVERSHOOTS DURING ENGINE START
  • NEW SOFTWARE TO UPDATE GFX-1060 MONITORS.
  • VEHICLES AFFECTED:
  • CHALLENGER: LEGACY COMBINES WITH AGCO POWER TIER3 ENGINES
  • FENDT: LEGACY COMBINES WITH AGCO POWER TIER3 ENGINES
  • LAVERDA: LEGACY COMBINES WITH AGCO POWER TIER3 ENGINES
  • MASSEY FERGUSON: LEGACY COMBINES WITH AGCO POWER TIER3 ENGINES
  • GENERAL:
  • FAULT TREES ENGINES UPDATED.
  • VEHICLES AFFECTED:
  • FENDT: 8380P, 8380P AL, 8410P, 8410P AL, 9490X, 9490X AL
  • MASSEY FERGUSON: 7380, 7380 AL, 7382, 7382 AL, 9380, 9380 AL
  • VEHICLE VERSION:
  • 2.25
  • GENERAL:
  • ADDED SOURCE ADDRESS FOR MAF SENSOR AUTOMATED VERSION DETECTION.
  • SOFTWARE:
  • ENGINE SOFTWARE SPEC. 84701 VER. ACX257104B_1
  • ENGINE SOFTWARE SPEC. 84739 VER. ACX257100B_1
  • ENGINE SOFTWARE SPEC. 84716 VER. ACX257103B_1
  • ENGINE SOFTWARE SPEC. 84738 VER. ACX257099B_1
  • ENGINE SOFTWARE SPEC. 98709 VER. ACX257107B_1
  • PLUG-INS:
  • AP T4F VER. 6.23
  • MFA VER. 8.10
  • VEHICLES AFFECTED:
  • CHALLENGER: MT600E WITH TMC DISPLAY
  • MASSEY FERGUSON: 8700 WITH DATATRONIC 5 SERIES
  • MASSEY FERGUSON: MF 8700S SERIES
  • VALTRA: S4 WITH SMARTTOUCH DISPLAY SERIES
  • VEHICLE VERSION:
  • 7.52
  • GENERAL:
  • ADD MF8727 TIER2 AND S274 TIER2 IN SOUTH AMERICA REGION
  • SOFTWARE:
  • NEW SRC14-34 SOFTWARE V6.14 FOR MF AND CHALLENGER MODELS:
  • FIX PICK UP HITCH WHICH WAS NOT WORKING PROPERLY SINCE V6.14
  • P20758 - FIX PTO AUTO WHICH WAS NOT WORKING IF FRONT HITCH COMMAND WAS DIFFERENT THAN NEUTRAL
  • P22189 - FIX DTM STATUS WHICH WAS NOT MEMORIZED AT KEY ON/OFF/ON
  • NEW TIER4F ENGINE SOFTWARE FOR 2ND TURBO ENGINE (84 AWF) :
  • NEW MAF CALIBRATION TO ENABLE USE NEW MASS AIR FLOW SENSOR
  • NEW STAGE5 ENGINE SOFTWARE (84 LFVC) :
  • FIX THE AIR MASS SENSOR OFFSET ZEROING ISSUE.
  • ACM
  • GW04 UPDATED TO V05.04.04 TO SUPPORT THE ENCRYPTED WIFI CONNECTION
  • GW03 REVERTED TO V05.01.06 WHICH IS THE LATEST VERSION COMPATIBLE WITH THE HARDWARE.
  • VEHICLES AFFECTED:
  • ATS: HIPER AG
  • VEHICLE VERSION:
  • 1.10
  • VEHICLES AFFECTED:
  • FENDT: IDEAL COMBINES
  • MASSEY FERGUSON: IDEAL COMBINES
  • VEHICLE VERSION:
  • 1.107
  • GENERAL:
  • NEW FEATURES:
  • CHAFF SPREADER SPEED SENSOR (IF EQUIPPED): USER CAN SEE THE CHAFFER SPEED AT THE BOTTOM OF THE “RESIDUE DISCHARGE” PAGE. WITH THIS FEATURE ENABLED AND SPEED SENSOR INSTALLED USER WILL GET AN ALARM WHEN THE CHAFF SPREADER SPEED DROPS BELOW 95 RPM, A CLASS 3 ALARM SHALL BE GENERATED: ""CHAFF SPREADER PLUGGED. TURN OFF THRESHER”
  • HILLSIDE AUDIBLE ALARM UPDATES: THE TI HEADLAND IDEAL FEATURE WILL NO LONGER BE AN OPTIONAL FEATURE. FROM THIS SOFTWARE RELEASE AND ON TI HEADLAND IDEAL WILL BE ENABLED BY DEFAULT ON ALL MACHINES.
  • UPDATES TO ENGINE COOLING FAN PITCH CONTROL: COOLING FAN PITCH HAS BEEN UPDATED TO ACHIEVE MAX PITCH ANGLE AT 88°C HYDRAULIC OIL TEMP. FROM A PREVIOUS TEMPERATURE OF 93°C, TO IMPROVE OIL COOL DOWN PROCESS.
  • MAN ENGINE TORQUE CURVE UPDATES: UPDATED STANDARD TORQUE CURVE TO MATCH BOOST TORQUE CURVE AT 1850 RPM AND BELOW ON ALL MAN ENGINES.
  • REPAIRS:
  • WAS CALIBRATION IMPROVEMENTS FOR IDEAL DRIVE: AFTER COMPLETION OF THE WAS CALIBRATION ON AN IDEAL DRIVE MACHINE, OPERATOR WILL BE PROMPTED WITH THE FOLLOWING TEXT: “KEY OFF FOR AT LEAST 5 SECONDS, KEY ON AND SELECT “UPDATE WAS NEUTRAL POSITION” TO COMPLETE NEUTRAL CALIBRATION”
  • CHOPPER CLUTCH DISENGAGEMENT: FIXED AN ISSUE WHERE THE CHOPPER CLUTCH WOULD NOT DISENGAGE IF MACHINE WAS TURNED OFF WHILE CHOPPER CLUTCH WAS ENGAGED.
  • DATA TRANSFER OPERATION VIA EDT UPDATES: UPDATES HAS BEEN MADE TO THE BACKUP AND RESTORE LOGIC TO BE MORE RELIABLE.
  • AUTO HEADER TILT UPDATES: NEW CONTROLLER FOR AUTOMATIC HEADER TILT. OPERATOR WILL NOTICE A SMOOTHER AND MORE RESPONSIVE TILT CONTROL.
  • STEERING VALVE FAILED TO POWER DOWN :FIXED ISSUE WHERE STEERING VALVE FAILED TO POWER DOWN WHEN OPERATOR ATTEMPTED TO GO INTO ROAD MODE (FC 240.520817.31).
  • SOFTWARE:
  • ACM VER. 5.4.4
  • ACM CONFIG VER. V12.1
  • EXT VER. CR.F.13.000.15.426110
  • NT01 VER. 13_0_24257
  • GQS VER. 1.0.8.3013
  • GDM VER. 13.01
  • ENGINE SOFTWARE SPEC. 98730 VER. ACX314682A_1
  • ENGINE SOFTWARE SPEC. 98732 VER. ACX314684A_1
  • PLUG-INS:
  • ACM VER. 6.19
  • AP T4F VER. 6.23
  • MFA VER. 8.10
  • VEHICLES AFFECTED:
  • MASSEY FERGUSON: 1E, 1M, 2E, 2MSERIES
  • VEHICLE VERSION:
  • 2.40
  • GENERAL:
  • INTRODUCTION OF THE 1E/M AND 2E/M SERIES TRACTORS INTO THE NORTH AMERICAN AND AUSTRALIA, NEW ZEALAND, AND JAPANESE MARKETS.
  • VEHICLES AFFECTED:
  • MASSEY FERGUSON: 4609M, 4610M, AND 4610M-HC
  • VEHICLE VERSION:
  • 2.16
  • SOFTWARE:
  • UPDATE ENGINE FILES.
  • VEHICLES AFFECTED:
  • FENDT: C-SERIES 2015: 5275CA, 5275CPLA, 6335CA, 6335CPLA
  • FENDT: L-SERIES 2015: 5255L, 6275L
  • LAVERDA: M300 SERIES 2015: M300A, M310A
  • LAVERDA: M400 SERIES 2015: M400A, M400LCA, M400LCIA, M410A, M410LCA
  • MASSEY FERGUSON: ACTIVA S SERIES 2015: 7345S, 7347S
  • MASSEY FERGUSON: BETA SERIES 2015: 7360A, 7360PLA, 7370A, 7370PLA
  • VEHICLE VERSION:
  • 2.37
  • GENERAL:
  • ADDED SOURCE ADDRESS FOR MAF SENSOR AUTOMATED VERSION DETECTION.
  • SOFTWARE:
  • ENGINE SOFTWARE SPEC. 84715 VER. ACX257101A_1
  • ENGINE SOFTWARE SPEC. 84740 VER. ACX257105A_1
  • ENGINE SOFTWARE SPEC. 84722 VER. ACX257102A_1
  • ENGINE SOFTWARE SPEC. 84751 VER. ACX257106A_1
  • PLUG-INS:
  • AP T4F VER. 6.23
  • MFA VER. 8.10
  • VEHICLES AFFECTED:
  • MASSEY FERGUSON: MF 3700 SERIES
  • MASSEY FERGUSON: MF 3X SERIES
  • VEHICLE VERSION:
  • 1.81
  • PLUG-INS:
  • NEW FPT STAGE5 PLUGIN (V1.6):
  • ADD EGR ACTUATOR TEST
  • ADD THROTTLE VALVE ACTUATOR TEST
  • ADD SCR EMPTYING TEST
  • ADD SCR DOSING TEST
  • VEHICLES AFFECTED:
  • FENDT: MOMENTUM LARGE
  • VEHICLE VERSION:
  • 2.13
  • GENERAL:
  • REGION: NORTH AMERICA, EASTERN EUROPE, AUSTRALIA
  • UPDATES:
  • ADDED VCT SHUT DOWN ALARMS
  • SENSOR ERROR ALARM
  • EXCEEDED MAX HEIGHT ALARM
  • ADDED ISOBUS SHORTCUT BUTTON (ISB) FUNCTIONALITY
  • ISB PRESSED ALARM
  • ADDED WEIGHT TRANSFER ALARM
  • LOADCELL ERROR ALARM
  • TIRE INFLATION SYSTEM UPDATES
  • ADDED TIRE INFLATION ALARMS
  • DRIVING TO FAST FOR WEIGHT AND SPEED
  • SPEED SENSOR ERROR
  • LOADCELL ERROR
  • LEAK DETECTED
  • TIRE PRESSURE TOO HHIGH
  • PRESSURE SENSOR ERROR
  • INLET PRESSURE TOO HIGH
  • UPDATE TIRE INFLATION UI MEANING
  • RED IS UNDERINFLATED FOR CONDITIONS
  • GREY IS WITHIN 5% OF TARGET
  • YELLOW IS OVER 15% OF TARGET (NOT AT MOST AGRONOMIC PRESSURE BUT OK TO OPERATE)
  • ADDED MAX SPEED TARGET FOR CURRENT WEIGHT AND PRESSURE
  • MANUAL MODE UPDATE
  • AUTOMATICALLY INCREASE PRESSURE IF NEEDED TO MEET LOAD/SPEED CONDITIONS.
  • WILL NOT DECREASE PRESSURE AFTER IT INCREASED IT.
  • DO NOT EXCEED MIN PRESSURE UPDATE
  • RESETS BASED ON LIFTED WEIGHT
  • DIAGNOSTIC UPDATES
  • LOGS UNDERINFLATED HOURS IN BOTH ROAD AND FIELD MODE
  • LOGS TOTAL HOURS SINCE 2.05 SOFTWARE UPDATE
  • ADDED MACHINE GEOMETRY ADJUSTMENTS
  • ROW SPACING
  • ROWS/SECTION
  • OFFSET FROM CENTER
  • AXLE DISTANCE FROM HITCH
  • SEEED EXIT FROM HITCH
  • AUTOLIFT AND MAPPING IMPROVEMENTS
  • SUPPORT FOR CONDENSED WORKSTATE VDRIVE MESSAGES
  • COMPATIBLE WITH 2025.1 2020 SOFTWARE ONLY
  • ADDED TASK CONTROLLER/ ICM DIAGNOSTIC PAGE
  • SHOWS ICM SECTION STATES AND TC SECTION STATES
  • SOFTWARE:
  • MOMENTUM LARGE V02.05.00
  • VEHICLES AFFECTED:
  • CHALLENGER: RG900C, RG 1100C, RG 1300C, RG1300C HT
  • ROGATOR: RG900C, RG 1100C, RG 1300C, RG1300C HT
  • VEHICLE VERSION:
  • 2.34
  • GENERAL:
  • IMPROVED IDENTIFICATION OF ACM HARDWARE AND SOFTWARE ON NETWORK SCAN
  • DIAGNOSTICS:
  • FIXED LINKS TO ELECTRICAL SCHEMATICS ON THE FOUR ""LIQUID VALVE LOCATION"" DIAGNOSTIC PAGES
  • CONFIGURATION:

 

  • CORRECTED MFA EEPROM UPDATE PROCESS IN THE NORMAL MFA SOFTWARE FLASH ROUTINE AND WHEN SELECTING “RESTORE CALIBRATIONS” USING THE ENGINEERING FUNCTION “WRITE MFA EEPROM FILE”. THIS CHANGE ALLOWS A TECHNICIAN TO COMPLETE AN MFA REPLACEMENT JOB WITHOUT CONTACTING SERVICE FOR A SPECIAL MFA FLASH AUTHORIZATION.
  • SOFTWARE:
  • ACM (VER 05.03.02) - GW04 HARDWARE ONLY
  • INCREASED STABILITY AND SIGNIFICANT TECHNICAL IMPROVEMENTS.
  • FIXED BUG WITH WHEN ACM WOULD CACHE LAST UPLOADED SECURE PACKAGE - EDGE CASES WHERE ACM WOULD NO LONGER ACCEPT CONFIG PACKAGES (IF SUPPORT TEAMS UPLOAD A WRONG FILE OVER THE FUSE PAGE, THEN ACM WILL NO LONGER ACCEPT ANY PACKAGE).
  • FIXED BUG WITH CALCULATION OF SIGNAL STRENGTH- ACM NO LONGER DISPLAY 116% SIGNAL STRENGTH ON THE FUSE PAGE, LOGS OR DIAGNOSTIC TERMINAL.
  • FIXED BUG WITH DATE TIME GETTING SHIFTED - INVALID GPS LOCK WOULD SET PREVIOUS DAY TIME, RESULTING IN ERRONEOUS DATA BEING UPLOADED TO THE CLOUD. NO MORE TIME STAMP ISSUES OR INVALID TIME ON DATA.
  • ACM (V05.01.06) - GW03 HARDWARE ONLY
  • LAST SOFTWARE UPDATE FOR OLDER GW03 HARDWARE.
  • ACM – IDCONFIG (RG3_V24_11/13/2023) – AVAILABLE THROUGH WIRELESS ACM UPDATE
  • ADDED CONDITIONS FOR TRANS-MODE_APPL UID 2684413188 TO CORRECTLY INDICATE STREET MODE
  • ACM – TELEMETRYCONFIG (APPLICATION_V14_04/02/2024) - AVAILABLE THROUGH WIRELESS ACM UPDATE
  • REMOVED UID 3489661044 TOTAL_AREA_DATA_LOGGER BECAUSE THIS VALUE IS NOT CALCULATED CORRECTLY ON THE MACHINE
  • ADDED WORK ON UID 2147483789 TO CORRECTLY DETERMINE MACHINE STATE
  • ACM – STATUSCALCCONFIG (APPLICATION_V3_9/30/2021) - AVAILABLE THROUGH WIRELESS ACM UPDATE
  • UPDATED TO COMMON FILE
  • WSM NEW LEADER SPREADER MODULE (V2.17.0.0):
  • NEW LEADER SPREADER SWATH MODULE (V2.7.0.0):

 

  • UPDATED FEEDGATE CONTROL LOOP
  • UPDATED ADVANCED PARAMETER DEFAULT VALUES
  • RAVEN VIPER4+ (V23.4.1.11):
  • LOCK UP DUE TO SERVICE TOOL ISSUE RELATED TO WIFI DROPS
  • RAVEN LEGACY CAN ECU’S NOT WORKING (ACCUBOOM, AUTOBOOM, ETC)
  • SLOW DOWN DUE TO ACCESSING SCOUT WIDGET LISTS
  • SINGLE PRODUCT WIDGET ASSIGNMENT STAYING ASSIGNED ON POWER CYCLE
  • AGSYNC FIXES
  • LARGE TIME JUMPS DUE TO STARTUP AND GPS/RS1 STARTUP
  • RAVEN RCM-U – FIRMWARE – 24.3.0.47
  • NEW FEATURES
  • ABILITY TO SET INDIVIDUAL MIN PWM% FOR LEFT & RIGHT CONVEYORS
  • DEFECT RESOLUTION
  • FIXED CONVERSION FOR BIN LEVEL SENSOR VALUES RECEIVED OVER CAN
  • RAVEN RS1 (V24.1.1.6):
  • NEW FEATURES
  • ADDED DYNAMIC HEIGHT ADJUSTMENT AND COMMUNICATION TO VSN
  • ADDED DIRECTSTEER INTEGRATION
  • ADDED SUPPORT FOR FENDT JOYSTICK DIRECTION SENSE
  • ENHANCEMENTS
  • ADD VERIZON CHECKBOX TO TOGGLE CELLULAR COMMUNICATION
  • ADD A HELP MENU ENTRY FOR WHEEL SPEED COMPENSATION
  • DEFECT RESOLUTION
  • FIX FOR TERRAGATOR B NOT PARING WITH SAUER VALVE
  • FIX TARGET WHEEL ANGLE READOUT NOT UPDATING IN HEALTH
  • SOLVED THE ISSUE WHERE THE ECU’S ARE UP TO DATE DIALOG WOULD RANDOMLY POP UP
  • BUG FIXES THAT IMPROVE SLINGSHOT POOL STABILITY
  • RAVEN VSN (V23.4.1.12):
  • CAMERA ROW GUIDANCE FAILURES UPON POWER CYCLE DUE TO DYNAMIC HEIGHT SOFTWARE ISSUE
  • ROW GUIDANCE RADAR PROGRAMMING UPDATE CAUSING UT LOCKUP
  • PLUG-INS:
  • UPDATED MFA PLUGIN TO 8.10
  • CORRECTED MFA EEPROM UPDATE PROCESS - ADDED A RESTORE_ROGATOR ENUM TO THE PLUGIN PARAMETER ERESTOREPARAMKALIB SO THE R9, RG3, R521, AND TG3 WILL BE ABLE TO LOAD THE ""PARAMETERS FOR ANALOG JOYSTICK"" FROM THE BASE EEPROM FILE.
  • UPDATED ACM PLUGIN TO 6.19
  • IMPROVED IDENTIFICATION OF ACM HARDWARE AND SOFTWARE VERSIONS
  • EDT CHOOSES WHICH SOFTWARE TO FLASH BASED ON HARDWARE VERSION OF CONNECTED ACM
  • CORRECTED ISSUE WITH ACM REPLACEMENT PROCESS
  • VEHICLES AFFECTED:
  • MASSEY FERGUSON: 5700 DYNA-4 TRACTORS
  • VALTRA: AC71.5
  • VEHICLE VERSION:
  • 2.60
  • SOFTWARE:
  • NEW ENGINE SOFTWARE FOR TIER4F 3 CYLINDER ENGINES (33AWFC):
  • UPDATE CALIBRATION TO IMPROVE BEHAVIOR AT INITIALIZATION AND PREVENT RAIL PRESSURE OVERSHOOTS DURING ENGINE START

 

  • NEW TRANSMISSION AND LINKAGE SOFTWARE V1.19.0 (MF ONLY):
  • P20842 - FIX REAR LINKAGE THAT CONTINUED TO MOVE AFTER ENGINE STALL / RESTART
  • VEHICLES AFFECTED:
  • ATS: SP008-WIPER-RETROFIT
  • VEHICLE VERSION:
  • 1.13
  • GENERAL:
  • CALIBRATION STABILITY UPDATE
  • DIAGNOSTICS:
  • GUI CHORE
  • INCREASED SIZE OF TEXTBOXES TO FIT ALL LANGUAGES
  • UPDATED TEXTTABLES FOR MORE CONSISTENCY
  • CALIBRATIONS:
  • REFACTORED CALIBRATION TIMING TO AVOID FALSE CALIBRATION ABORTS
  • CONFIGURATION:
  • N/A
  • DIAGNOSTIC TESTS:
  • N/A
  • SOFTWARE:
  • N/A
  • DIAGNOSTIC TROUBLE CODES:
  • N/A
  • PLUG-INS:
  • N/A
  • VEHICLES AFFECTED:
  • VALTRA: S3 SERIES
  • VALTRA: S4 SERIES
  • VEHICLE VERSION:

 

  • 8.71
  • SOFTWARE:

 

  • NEW TIER4F ENGINE SOFTWARE WHICH SETS THE MAF CALIBRATION TO ENABLE USE NEW MASS AIR FLOW SENSOR
  • VEHICLES AFFECTED:
  • GLEANER: S96, S97, S98
  • VEHICLE VERSION:
  • 5.84
  • GENERAL:
  • SOFTWARE AND PLUG-IN UPDATE
  • SOFTWARE:
  • ACM VER. 5.4.4
  • EXT VER. CT.F.25.000.07.419716
  • NT01 VER. 24.06.24225
  • NT01 EEPROM VER.01_17_23_2
  • PLUG-INS:
  • ACM VER. 6.19
  • CEA GUIDE VER. 8.33
  • AP T4F VER. 6.23
  • MFA VER. 8.10
  • VEHICLES AFFECTED:
  • CHALLENGER: TG7300C, TG8300C, TG8400C, TG9300C
  • TERRAGATOR: TG7300C, TG8300C, TG8400C, TG9300C
  • VEHICLE VERSION:
  • 1.104
  • CONFIGURATION:
  • CORRECTED MFA EEPROM UPDATE PROCESS IN THE NORMAL MFA SOFTWARE FLASH ROUTINE AND WHEN SELECTING “RESTORE CALIBRATIONS” USING THE ENGINEERING FUNCTION “WRITE MFA EEPROM FILE”. THIS CHANGE ALLOWS A TECHNICIAN TO COMPLETE AN MFA REPLACEMENT JOB WITHOUT CONTACTING SERVICE FOR A SPECIAL MFA FLASH AUTHORIZATION.
  • ADDED THE ABILITY TO RESET THE DASHBOARD HOURS.
  • SOFTWARE:
  • WSM NEW LEADER SPREADER MODULE (V2.17.0.0):
  • NEW LEADER SPREADER SWATH MODULE (V2.7.0.0):
  • UPDATED FEEDGATE CONTROL LOOP
  • UPDATED ADVANCED PARAMETER DEFAULT VALUES
  • RAVEN VIPER4+ (V23.4.1.11):
  • LOCK UP DUE TO SERVICE TOOL ISSUES RELATED TO WIFI DROPS
  • RAVEN LEGACY CAN ECUS NOT WORKING (ACCUBOOM, AUTOBOOM, ETC)
  • SLOW DOWN DUE TO ACCESSING SCOUT WIDGET LISTS
  • SINGLE PRODUCT WIDGET ASSIGNMENT STAYING ASSIGNED ON POWER CYCLE
  • AGSYNC FIXES
  • LARGE TIME JUMPS DUE TO STARTUP AND GPS/RS1 STARTUP
  • RAVEN RCM-U – FIRMWARE (V24.3.0.47)
  • NEW FEATURES
  • ABILITY TO SET INDIVIDUAL MIN PWM% FOR LEFT & RIGHT CONVEYORS
  • DEFECT RESOLUTION
  • FIXED CONVERSION FOR BIN LEVEL SENSOR VALUES RECEIVED OVER CAN
  • RAVEN RS1 (V24.1.1.6):
  • NEW FEATURES
  • ADDED DYNAMIC HEIGHT ADJUSTMENT AND COMMUNICATION TO VSN
  • ADDED DIRECTSTEER INTEGRATION
  • ADDED SUPPORT FOR FENDT JOYSTICK DIRECTION SENSE
  • ENHANCEMENTS
  • ADD VERIZON CHECKBOX TO TOGGLE CELLULAR COMMUNICATION
  • ADD A HELP MENU ENTRY FOR WHEEL SPEED COMPENSATION
  • DEFECT RESOLUTION
  • FIX FOR TERRAGATOR B NOT PARING WITH SAUER VALVE
  • FIX TARGET WHEEL ANGLE READOUT NOT UPDATING IN HEALTH
  • SOLVED THE ISSUE WHERE THE ECU’S ARE UP TO DATE DIALOG WOULD RANDOMLY POP UP
  • BUG FIXES THAT IMPROVE SLINGSHOT POOL STABILITY
  • PLUG-INS:
  • UPDATED MFA PLUGIN TO 8.10
  • CORRECTED MFA EEPROM UPDATE PROCESS - ADDED A RESTORE_ROGATOR ENUM TO THE PLUGIN PARAMETER ERESTOREPARAMKALIB SO THE R9, RG3, R521, AND TG3 WILL BE ABLE TO LOAD THE ""PARAMETERS FOR ANALOG JOYSTICK"" FROM THE BASE EEPROM FILE.
  • UPDATED ACM PLUGIN TO 6.19
  • CORRECTED ISSUE WITH ACM REPLACEMENT PROCESS
  • VEHICLES AFFECTED:
  • GLEANER: T61, T71, T81
  • VEHICLE VERSION:
  • 0.18
  • GENERAL:
  • FIRST EDT RELEASE FOR NEW CT-25M SERIES
  • SOFTWARE:
  • ACM VER. 5.4.4
  • YMM VER. 1.6.0.0
  • PVED-CC VER. 1.65
  • SPM VER. 14101$A.S19
  • EXT VER. 25.000.07
  • NT01 VER. 24_06_24255
  • NT01 EEPROM VER. 01_17_23_2
  • GDM VER. CT25_24_0501
  • CEDC VER. 4.9
  • HCDM1 VER. 2.0
  • HCDM2 VER. 2.0
  • VMM1 VER. 0.3
  • VMM2 VER. 0.3
  • VD0X VER. B.01.039.00
  • HVAC VER. 1.0.10.200
  • LCP VER. 0.50
  • MFA VER. 2.92
  • T4F ENGINE SOFTWARE SPEC. 84700 VER. ACX4564230
  • T4F ENGINE SOFTWARE SPEC. 98700 VER. ACX351690A_1
  • T4F ENGINE SOFTWARE SPEC. 98701 VER. ACX351689A_1
  • LRC ENGINE SOFTWARE SPEC. 84721 VER. ACX4564260
  • LRC ENGINE SOFTWARE SPEC. 98714 VER. ACX351693A_1
  • LRC ENGINE SOFTWARE SPEC. 98713 VER. ACX351694A_1
  • PLUG-INS:
  • ACM VER. 6.19
  • CEA GUIDE VER. 8.33
  • AP T4F VER.6.23
  • HVAC VER. 8.4
  • LCP VER. 8.7
  • MFA VER. 8.10
  • VEHICLES AFFECTED:
  • VALTRA: F SERIES
  • VEHICLE VERSION:
  • 1.8
  • GENERAL:
  • ADD FRONT AXLE SUSPENSION SUPPORT (NETWORK SCAN, DIAGNOSTIC, DTC)
  • ADD ELECTRONIC LINKAGE SUPPORT (DTC ONLY FOR THE MOMENT)
  • SOFTWARE:
  • NEW TCU SOFTWARE FOR STAGE5 MODELS
  • ADD STAGE5 ENGINE SOFTWARE
  • PLUG-INS:
  • NEW FPT STAGE5 PLUGIN:
  • ADD ENGINE DIAGNOSTIC TESTS
  • ADD FLASH OF SOFTWARE FUNCTIONALITY
  • VEHICLES AFFECTED:
  • VALTRA: BH G4, BH214 HITECH, BH224 HITECH
  • VEHICLE VERSION:
  • 3.12
  • GENERAL:
  • NEW SOFTWARE VERSION 14.40.000.01.4 IS NOW AVAILABLE FOR UPDATING GFX-750 AND GFX-1060 MONITORS FOR TRACTORS.
  • DISABLED GFX750/1060 FOR REGIONS OUTSIDE OF SOUTH AMERICA
  • SOFTWARE:
  • GFX-1060 SW 14.40.000.01.4
  • AGCO CONNECTIVITY MODULE SOFTWARE VERSION 5.04.04
  • PLUG-INS:
  • GFX750 VERSION 1.4
  • VEHICLES AFFECTED:
  • VALTRA: T4-SERIES 1A7 / 1B8, N4-SERIES 1B7 / 1C8
  • VEHICLE VERSION:
  • 1.109
  • SOFTWARE:
  • SOFTWARE PACKAGE 1.14.0
  • DIRECT TC1 APPLICATION
  • FIX FOR PTO PULLING DEFECT
  • FIX FOR CLUTCH PEDAL SLIPPING PROBLEM
  • FIX FOR ENGINE RPM SWINGING AFTER START
  • VERSU TC1 APPLICATION
  • FIX FOR CLUTCH PEDAL SLIPPING PROBLEM
  • VEHICLES AFFECTED:
  • CHALLENGER: MT600E SERIES
  • MASSEY FERGUSON: 8700 SERIES
  • VEHICLE VERSION:
  • 6.61
  • SOFTWARE:
  • NEW TIER4F ENGINE SOFTWARE (84 AWF NEW TURBO & 84 AWF NEW TURBO WITH DEF QUALITY SENSOR) :
  • NEW MAF CALIBRATION TO ENABLE USE NEW MASS AIR FLOW SENSOR
  • VEHICLES AFFECTED:
  • CHALLENGER: MT400E SERIES
  • CHALLENGER: MT500E SERIES
  • ISEKI: I5700 SERIES
  • ISEKI: I6700 SERIES
  • ISEKI: I7700 SERIES
  • MASSEY FERGUSON: 5700S SERIES
  • MASSEY FERGUSON: 5700SL SERIES
  • MASSEY FERGUSON: 6700S SERIES
  • MASSEY FERGUSON: 7700 MADE IN BRAZIL SERIES
  • MASSEY FERGUSON: 7700 SERIES
  • MASSEY FERGUSON: 7700S SERIES
  • VALTRA: T195-250 SERIES
  • VEHICLE VERSION:
  • 8.24
  • SOFTWARE:
  • NEW TIER4F ENGINE SOFTWARE :
  • P21403 - CHANGE ENGINE RPM AT WHICH INJECTION CUT TO AVOID STALLING WHEN ACTIVATING PTO

 

  • NEW TIER3 ENGINE SOFTWARE :
  • P21403 - CHANGE ENGINE RPM AT WHICH INJECTION CUT TO AVOID STALLING WHEN ACTIVATING PTO
  • ACM
  • GW04 UPDATED TO V05.04.04 TO SUPPORT THE ENCRYPTED WIFI CONNECTION
  • GW03 REVERTED TO V05.01.06 WHICH IS THE LATEST VERSION COMPATIBLE WITH THE HARDWARE.
  • VEHICLES AFFECTED:
  • CHALLENGER: MT400D SERIES
  • CHALLENGER: MT500 D SERIES
  • ISEKI: I6600 SERIES
  • ISEKI: I7600 SERIES
  • MASSEY FERGUSON: 6600 SERIES
  • MASSEY FERGUSON: 7600 SERIES
  • VEHICLE VERSION:
  • 10.91
  • SOFTWARE:
  • NEW TIER2 ENGINE SOFTWARE (66LFEN)
  • P21403 - CHANGE ENGINE RPM AT WHICH INJECTION CUT TO AVOID STALLING WHEN ACTIVATING PTO"

Support models

Compatible Vehicles

No information available
  • LAVERDA ONLY WORKS IN THE "EASTERN EUROPE" REGION